THE PROFESSIONAL HAVOC
 
Novak`s Havoc Pro Brushless ESC (#1735) tops the list in the Havoc line because of its unmatched speed, economical price and advanced compatibility: The Havoc Pro is compatible with the entire Novak 540-sized brushless motor line and any ROAR-approved 540-sized sensored motor, all the way down to 3.5-turns.
 
A LOT OF PROGRAMMING IN A SMALL PACKAGE
Novak has packed the Havoc Pro Brushless ESC full of programmability into one easy-to-adjust profile. The Havoc Pro includes a customizable Throttle Curve, which smoothes out throttle operation. In addition, the Havoc Pro’s Brake Frequency adjustment contains seven degrees of adjustability from a smooth and controllable brake to a more abrupt and grabbier feel. The dozens of adjustments allow drivers to fine-tune their vehicle’s throttle braking for better control and advanced handling.
 
 
 
 
 
 
 
 
 

 
 
 
Havoc Pro/Ballistic Brushless System installed in a Team Associated® SC10™ Short Course Truck.
 
But the customization doesn’t end with braking. Novak also has built-in Battery Type Selection that auto detects among Li-Po, Li-Fe and Ni-MH batteries and prevents them from going below the critical safety voltage level, and a Motor Rotation feature that allows the user to easily select the direction of the motor.
 
MOTOR COMPATIBILITY
The Havoc Pro ESC is compatible with all Novak brushless motors and any ROAR-approved 540-sized sensored motor, all the way down to 3.5-turns. 
 
 
 
 
 
 
 
The Havoc Pro Brushless ESC is compatible with five Ballistic motors: 3.5T (#3130), 6.5T (#3132), 10.5T (#3133), 13.5T (#3134) and 17.5T (#3135).

 
 
 
 
 
 
 
 
 
HAVOC PRO BRUSHLESS ESC FEATURES
 
 
 
Nine adjustable parameters: Minimum Brake (10 settings from 0-30%), Drag Brake (10 settings from 0-30%), Dead Band (5 settings from 2-6%), Minimum Drive (5 settings from 1-12%), Throttle Curve (Linear, Expo-1 and Expo-2), Brake Frequency (7 settings from 1-8 kHz), Reverse, Motor Rotation and Battery Pack Selection (Li-Po, Li-Fe, Ni-MH)
 
 
 
Fifty percent more transistors than the Havoc 2S ESC for faster speeds, higher efficiency and increased load handling
 
 
 
One-Touch Set-Up for quick, easy transmitter setup 
 
 
 
Locked Rotor Detection and Thermal Overload Protection (when used with a Novak sensored brushless motor) 
 
 
 
Novak’s Radio-Priority and Polar Drive Circuits 
 
 
 
Included 30x30x6mm ESC clear cooling fan (#5648) mounted on factory-installed heat sink
 
 
 
Meets RoHS compliance and includes 120-Day Warranty
 
 
 
Designed, assembled and tested by Novak in Irvine, Calif., using globally sourced components
 
 
 
 
 
 
 
HAVOC PRO BRUSHLESS ESC SPECS
 
 
 
Input Voltage: 2S Li-Po cells, 2S Li-Fe cells or 4-6 NiMH cells (1.2V/cell) 
 
 
 
ESC Footprint: 1.16” x 1.49” (29.5 x 37.8 mm) 
 
 
 
Weight (without wires): 1.36 oz. (38.5 g)
 
 
 
Design: Sensor-based
 
 
 
Motor Limit (brushless): All 3.5-turn Novak 540-size sensored brushless motors
 
 
 
On-Resistance (brushless): 0.00040 ohms @ 25°C trans. temp. 
 
 
 
BEC: 6.0 volts DC / 3.0 amps
 
 
 
Rated Current: 540 Amps @ 25°C trans. temp.
 
 
 
Braking Current: 540 Amps @ 25°C trans. temp.
 
 
 
Status LEDs: 4
 
 
 
Voltage Cut-Off: 6.25V (Li-Po), 4.75V (Li-Fe)
 
 
 
Power Wires: 14G Super-Flex Copper-Strand Silicone Wire
 
 
 
 
 
 
 
REPLACEMENT / OPTIONAL PARTS
 
 
 
#5315 or #5320 User-replaceable Input Harness (replacement) 
 
 
 
#5508 14-Gauge Silicone Brushless Wire Set (replacement)
 
 
 
#5602 Remote Power Programming Switch (replacement) 
 
 
 
#5648/#5652 Clear Cooling Fan 30x30x6mm (replacement) 
 
 
 
#5679 Power Trans-Cap Module -- 2S Li-Po and 4-6 cell NiMH (replacement)
 
 
 
#5731 3.5mm Low-Loss Power Connectors – 5 pairs (optional)


 
 
 
 
 
Havoc Pro Set-Up Instructions
 
 
 
ESC Spec Chart
 
 
 
 
 
 
  
To view a slideshow featuring Novak`s 
complete line of Havoc products, click here.
 
One-Touch Set-Up™ and Smart Braking II™ are registered trademarks of Novak Electronics, Inc.®.